首先看看檢查步驟:先從檢查控制機房的欠水超溫保護器開始,看看恒溫恒濕試驗箱是否設定在150℃的位置;若沒有設定在150℃的位置,請將欠水超溫保護器轉至150℃的位置;再檢查機房內,管路是否過臟,造成水流不順;解決方法:請先將機臺后方總電源關上,然后將加濕桶下方的排水閥,打開到與管路平行的位置,待上水箱的水都排光的時候,利用板手將加濕桶打開,將內部因長期做濕度而產生的水垢清除,然后將硅膠管路拔除,在水中搓洗,保養完畢后按照拆除的方式,反方向裝回去,裝置完畢后,需將加濕桶下方的排水閥,關閉到與管路垂直的位置,然后再將機臺后方總電源打開。
再看看上水箱是否有水,若無水,再檢查下水箱是否有水;解決方案:上下水箱都無水,請將下水箱加水,即可解決。上水箱若無水,下水箱有水,則為下水箱打水馬達壞掉,請通知鴻達天矩公司維修客服部門上門進行維修。
最后請檢查恒溫恒濕試驗箱是否濕度部份的固態繼電器燒毀短路:若加熱器未燒毀,請使用三用電表交流電壓檔,電壓檔位開到600伏特的位置,將紅黑棒分別放在線號標注為H的那一顆固態繼電器交流兩側,將濕度部份的濕度設定值設置0%,此時濕度部份的固態繼電器的指示燈不會亮起,若量測的電壓值沒有變化,維持在10V以下代表固態繼電器燒毀呈現短路狀態。或先將濕度部份設定值設為0%,再看機房內加濕桶是否水在煮沸狀態。
如何選購恒溫恒濕箱的規格尺寸
恒溫恒濕試驗箱適用于電工、設備及其它產品、零部件及材料在高低溫、濕熱環境下貯存、運輸、使用時的適應性試驗,是各類、電工、電器、塑膠等原材料和器件進行耐寒、耐熱、耐濕、耐干性試驗及品管工程的可靠性測試設備,特別適用于光纖、LED、晶體、電感、PCB、電池、電腦、手機等產品的耐高溫、耐低溫、耐濕熱循環試驗。
選擇一款合適的恒溫恒濕試驗箱規格尺寸,對于以后的試驗來說,將起到事半功倍的效果。首先是恒溫恒濕試驗箱容積的選擇,選購者可將被試產品(元器件、組件、部件或整機)置入氣候環境箱進行試驗時,為了保證被試產品周圍氣氛能滿足試驗規范所規定的環境條件,氣候箱工作空間尺寸與被試產品外廓尺寸之間應遵循以下幾點規定:
a) 被試產品的體積(W×D×H)不得超過試驗箱有效工作空間的(20-35)(推薦選用20)。對于在試驗中發熱的產品推薦選用不大于30;
b)被試產品的迎風斷面積與該斷面上試驗箱工作腔總面積之比不大于(35-50)(推薦選用35);
c)被試產品外廓表面距試驗箱壁的距離至少應保持100-150mm,(推薦選用150mm)。
東莞恒工設備是從事恒溫恒濕試驗箱,步入式環境試驗室,快速溫變試驗箱,冷熱沖擊試驗箱,高低溫低氣壓試驗箱,UV光照氣候試驗箱,電池熱沖擊試驗箱,高溫時效爐等設備研發和生產廠家之一,恒溫恒濕試驗箱,恒溫恒濕箱,高低溫箱,冷熱沖擊試驗箱,高低溫沖擊試驗箱具有行業領先地位,累積豐富行業經驗,具產品開發能力,獲多項國家專利,業務聯系:潘先生